Canon EOS 5D Mark IV Manual Focus

The Canon 5D mark iv dates to 2016 f0r stills, and to 2008 and the 5D Mk II for video. With the Mark IV, video is knock to DCI 4K (4096 x 2160 pixels) at 24 or 30 outlines for every second for up to 30 minutes for each clasp. There's additionally Full HD video (1920 x 1080) at up to 60 fps, or HD (720p or 1280 x 720) at up to 120 fps for quarter-speed moderate movement. The drawback to shooting 4K on the Mark IV is that Canon took the 6720 x 4480 sensor and simply utilize the middle 4096 x 2160 pixels. That flawlessly comprehends the issue of down sampling on the fly with potential quality issues, yet it likewise implies a harvest component of 1.74x. Pick the new 24-105mm Canon L Series focal point, regularly considered the ideal ordinary focal point, to shoot video and the compelling central length bounced to 42-165mm. What was a moderate wide-point to direct fax turns into an ordinary to-zooming focal point

Canon EOS 5D Mark IV Manual Focus

Canon EOS 5D Mark IV Manual Focus 

Selecting the AF Operation

For the Canon EOS 5D mark iv manual focus better than eos mark iii or eos 5d mark ii. You can select the AF operation characteristics to suit the shooting conditions or subject. In the <A> mode, [One Shot AF] is set automatically.
  1. Press the <Drive+AF> button.
  2. Select the AF operation. Turn the dial to select the desired AF operation, then press<set>.

One-Shot AF for Still Subjects

Suited for still subjects. When you press the shutter button halfway, the camera will focus only once.
  • When focus is achieved, the AF point will turn green.
  • The focus remains locked while you hold down the shutter button halfway, allowing you to recompose the image before taking the picture.
One-Shot AF for Still Subjects
  • Settable only for Live View shooting (not settable for movie shooting).
  • If focus cannot be achieved, the AF point will turn orange. If this occurs, the picture cannot be taken even if the shutter button is pressed completely. Recompose the shot and try to focus again. Or, see “Shooting Conditions that Make Focusing Difficult” .

Servo AF for Moving Subjects

From the EOS 5D mark iv  manual this AF operation is suited for moving subjects. While you hold down the shutter button halfway, the Canon camera will keep focusing on the subject continuously.
  • When the drive mode is set to  for high-speed continuous shooting, the maximum continuous shooting speed will be approx. 4.3 shots/sec. The pictures will be taken with priority given to the continuous shooting speed. With the low-speed continuous shooting setting, “Subject-tracking priority” will be used for shooting.
  • Canon eos mark iv For flash photography, the continuous shooting speed will become slower.
  • When focus is achieved, the AF point will turn blue.
  • The exposure is set at the moment the picture is taken.
  • When [AF method] is set to [u+Tracking] or [Flexizone - Multi], focusing will be continuous as long as the area frame can track the subject.
  • Servo AF for Moving Subjects
  • Depending on the lens used, the distance to the subject, and the subject’s speed, the camera may not be able to achieve correct focus.
  • Zooming during continuous shooting may throw off the focus. Zoom first, then recompose and shoot.
  • When [Servo AF] is set, the image-recording quality cannot be set to 41 or 61. If 41 or 61 is set, the image will be recorded in quality.
  • When [Servo AF] is set and [Multi Shot Noise Reduction] is set, [High ISO speed NR] will automatically switch to [Standard].
  • If [Servo AF] is set, pressing the button assigned for the function will not take effect if you set 41 or 61 image-quality for the [One-touch image quality setting] or [One-touch image quality (hold)] with [Custom Controls].
  • With Servo AF, the beeper will not sound even when focus is achieved
Canon EOS 5D Mark IV Manual Focus

Canon EOS 5D Mark IV Focusing with AF (AF Method)

You can set the EOS 5D AF method to suit the shooting conditions and subject.
If you want to achieve precise focus, set the lens’s focus mode switch to <MF>, magnify the image, and focus manually.
Select the AF method.
  • Under the [z5] tab (the [z3] tab in <A> mode), select [AF method].
  • Select the desired AF method, then press <set>.
  • When the Live View image is displayed, you can press the <drive+AF> button to select the AFoperation.
The camera detects and focuses on human faces. If a face moves, the AF point <p> also moves to track the face.
1 Display the Live View image.
  • Press the <0> button.
  • The Live View image will appear on the LCD monitor.
2 Select an AF point.
  • When a face is detected, the area frame will be displayed and <p> will appear over the face to be focused on.
  • If multiple faces are detected, <q> will be displayed. Use <9> to move <q> over the face you want to focus on.
  • You can also tap on the LCD monitor screen to select the face or subject. If you tap on a subject other than a human face, the AF point will be switched to < >.
3 Focus on the subject.
  • Press the shutter button halfway to focus.
  • If no faces can be detected or if you do not tap anything on the screen, the camera will switch to FlexiZone - Multi.
  • When focus is achieved, the AF point will turn green and the beeper will sound.
  • If focus is not achieved, the AF point will turn orange.
4 Take the picture.
Check the canon mark iv focus and exposure, then press the shutter button completely to take the picture.
Focusing on a subject other than a human face
  • Tap on the subject (or spot) where you want to focus.
  • Press <set> and the AF point will appear on the screen. Then use to move the AF point over the target subject.
  • Once the AF point achieves focus, it will track the subject even if the subject moves or if you change the composition
You can use up to 63 AF points for wide-area focusing (automatic selection). This wide area can also be divided into 9 zones for focusing (zone selection).
1 Display the Live View image.
  • Press the <set> button.
  • The Live View image will appear on the LCD monitor.
2 Select the AF point.N
  • Pressing <set> will toggle between automatic selection and zone selection. In the <A> mode, automatic selection is set automatically.
  • Use to select the zone. To return to the center zone, press <set> again.
  • You can also tap on the LCD monitor screen to select a zone. When a zone is selected, tap on the screen to switch to automatic selection.
3 Focus on the subject.
  • Aim the AF point over the subject and press the shutter button halfway.
  • When focus is achieved, the AF point will turn green and the beeper will sound.
  • If focus is not achieved, the area frame will turn orange.
4 Take the picture.
  • Check the focus and exposure, then press the shutter button completely to take the picture.

 Flexy Zone Multy

The camera focuses with a single AF point. This is effective when you want to focus on a particular subject.

1Display the Live View image.
  • Press the <set> button.
  • The Live View image will appear on the LCD monitor.
  • The AF point will appear.
  • If [Movie servo AF] is set to [Enable], the AF point will be displayed larger.
2 Move the AF point.
  • Use to move the AF point to where you want to focus. (It cannot be moved to the edge of the screen.)
  • Using <set> will return the AF point to the screen center.
  • You can also tap on the LCD monitor screen to move the AF point.
3 Focus on the subject.
  • Aim the AF point over the subject and press the shutter button halfway.
  • When focus is achieved, the AF point will turn green and the beeper will sound.
  • If focus is not achieved, the AF point will turn orange.
4 Take the picture.
Check the focus and exposure, then press the shutter button completely to take the picture

AF Operation
  1. Even when focus is achieved, pressing the shutter button halfway will focus again.
  2. The image brightness may change during and after the AF operation.
  3. Depending on the subject and shooting conditions, it may take longer to focus or the continuous shooting speed may decrease.
  4. If the light source changes while the Live View image is displayed, the screen may flicker and focusing may be difficult. If this happens, exit Live View shooting and perform AF under the actual light source under which you are shooting. Shooting Conditions that Make Focusing Difficult
  5. Subject with low-contrast such as the blue sky, solid-color flat surfaces or when highlight or shadow details are clipped.
  6. Subjects in low light.
  7. Stripes and other patterns where there is contrast only in the horizontal direction.
  8. Subjects with repetitive patterns (Example: Skyscraper windows, computer keyboards, etc.).
  9. Fine lines and subject outlines.
  10. Under a light source whose brightness, color, or pattern keeps changing.
  11. Night scenes or points of light.
  12. The image flickers under fluorescent or LED lighting.
  13. Extremely small subjects.
  14. Subjects at the edge of the picture.
  15. Strongly backlit or reflective subjects (Example: Car with a highly reflective body, etc.).
  16. Near and distant subjects covered by an AF point (Example: Animal in a cage, etc.).
  17. Subjects that keep moving within the AF point and will not stay stilldue to camera shake or subject blur.
  18. Performing AF when the subject is very far out of focus.
  19. Soft focus effect is applied with a soft focus lens.
  20. A special effect filter is used.
  21. Noise (dots of light, banding, etc.) appears on the screen during AF.

Canon EOS 5D Mark IV FlexiZone Multi

In the [FlexiZone - Multi] and [FlexiZone - Single] modes, either press the <u> button or tap on displayed on the bottom right of the screen. You can magnify the image by approx. 5x or 10x and check the focus.
Magnified view is not possible with [u+Tracking].
  • To move the AF point or select a zone, operate or tap on the spot you want to magnify.
  • Either press the button to magnify the image. Each time you press the button or tap on, the magnification ratio changes.
  • When [FlexiZone - Multi] is set, the image will be magnified at the center of the zone frame (or image center with automatic selection). When [FlexiZone - Single] is set, the image will be magnified at the AF point.
  • At 100% (approx. 1x) magnification, operate or tap on the screen to move the magnifying frame. Pressing <set> will return the magnifying frame to the screen center.
  • Either press the button or tap on to magnify the area covered by the magnifying frame.
  • When the image is magnified by approx. 5x or 10x, you can change the magnified area by operating or tapping on the triangle on the screen top, bottom, left, or right.
  • When you press the shutter button halfway, the normal view will return for [FlexiZone - Multi]. For [FlexiZone - Single], AF will proceed with the magnified view.
  • With Servo AF and magnified view, pressing the shutter button halfway will return to the normal view for focusing.

Canon EOS 5D Mark IV Shooting with the Touch Shutter

Just by tapping on the LCD monitor screen, you can focus and take the picture automatically.
1 Display the Live View image.
  • Press the <set> button.
  • The Live View image will appear on the LCD monitor.
2 Enable the touch shutter.
  • Tap [y] on the screen’s bottom left. Each time you tap on the icon, it will toggle between.
  • (Touch shutter: Enable) The camera will focus on the spot you tap on, then the picture will be taken.
  • (Touch shutter: Disable)
  • You can tap on a spot to perform focusing on the spot. Press the shutter button completely to take the picture.
3 Tap on the screen to shoot.
  • Tap on the face or subject on the screen.
  • On the point you tap, the camera will focus (Touch AF) with the AF method that was set.
  • When  is set, the AF point turns green when focus is achieved, then the picture is taken automatically.
  • If focus is not achieved, the AF point turns orange and the picture cannot be taken. Tap on the face or subject on the screen again.

Canon EOS 5D Mark IV MF: Focusing Manually

You can magnify the image and focus precisely with MF (manual focus).
1 Set the lens’s focus mode switch to <MF>.
  • Turn the lens focusing ring to focus roughly.
2 Display the magnifying frame.
  • Press the <u> button or tap on the lower right of the screen.
  • The magnifying frame will appear.
3 Move the magnifying frame.
  • Either operate <set> or tap on the spot you want to magnify to move the magnifying frame to where you want to focus.
  • Pressing <set> will return the magnifying frame to the screen center.
4 Magnify the image.
  • Each time you press the button on the lower right of the screen, the display will change in the following sequence:
  • While in magnified view, you can operate tap on the triangle displayed on the top, bottom, left, or right of the screen to scroll around the magnified image.
5 Focus manually.
  • While looking at the magnified image, turn the lens focusing ring to focus.
  • After achieving focus, press the button to return to the normal view.
6 Take the picture.
  • Check the exposure, then press the shutter button completely to take the picture
Advertismen

0 komentar:

Post a Comment